G-Mark, SASO and SABER: Getting a Distribution Box Into Saudi Arabia (2026)

  • This topic is empty.
Viewing 1 post (of 1 total)
  • Author
    Posts
  • #13849
    admin
    Keymaster

      Search for G-Mark certification requirements for distribution boxes in Saudi Arabia and the answer comes back as one line: get the mark. That line costs money. A board built to IEC 61439 is not on the list that requires a G-Mark, and the instrument that actually holds the container at Jeddah is one almost nobody names.

      Published: December 2026 | By LUJIEMAO Engineering Team

      1. What the G-Mark list actually contains

      Start with the legal text, because G-Mark certification requirements for distribution boxes in Saudi Arabia come from one document: the Gulf Technical Regulation for Low Voltage Electrical Equipment and Appliances, BD-142004-01, in force since 1 July 2016. Its scope reads broad — devices, appliances and fixtures rated 50 to 1000 V AC or 75 to 1500 V DC — less the Annex 2 exclusions covering explosive atmospheres, medical equipment, lift parts and electricity meters.

      A definition is not a mandate. Article 20 hands implementation to the Gulf Committee of Conformity Assessment, which publishes two lists by hazard. List 2 is the one in force: document TC-143307-01, thirteen categories that read like a white goods catalogue — fans, refrigerators, washers, mixers, toasters, hair dryers, heaters, microwaves, cookers, water heaters, irons — plus plugs, sockets, adaptors, cord sets and chargers.

      A distribution board is not in that list. Nor is a control cabinet or an assembly of any kind. List 1, the lower-hazard route where a manufacturer self-declares, has never been published — GSO's own guidance says there is no equipment in it and no schedule for one. A board therefore has no mark to obtain.

      ✅ Bottom line: A board without a G-Mark is not missing a certificate. On today's lists it has none to obtain.

      The complication is honest: consultants do write G-Mark into Saudi specifications, and a notified body will run a voluntary type examination on an assembly. Neither makes the mark an import requirement for HS 8537.10. If a specification cites it, ask which list item the board falls under — that question separates a regulation from a preference.

      2. The regulation that does gate it is about EMC

      Here is the instrument the trade pages skip. SASO published an Electromagnetic Compatibility Technical Regulation on 17 November 2023, in force from 17 May 2024, and Annex I lists the standards in scope. Item 52 is IEC 61439-4, assemblies for construction sites.

      A site box is therefore captured by a Saudi EMC regulation, by name. At the PCoC stage the file needs two things a safety report does not supply: a declaration of conformity, and an EMC test report from an accredited laboratory. For an assembly the generic standards are the industrial pair, SASO IEC 61000-6-2 for immunity and SASO IEC 61000-6-4 for emission.

      Harder than it sounds, because an empty enclosure has nothing to measure. The EMC file follows the devices inside: an unsuppressed contactor coil, a variable speed drive, a smart meter. Emission and immunity become properties of the configuration, exactly as temperature rise does under 61439. Change the fitted devices and the evidence describes a different product. Under the SASO RoHS regulation a certificate is also a prerequisite before any of these registrations.

      3. Inside the SABER application

      The SASO SABER registration process for imported distribution boxes has one structural feature that decides everything else: only a Saudi importer holding a valid commercial registration can open the file. A Chinese factory cannot apply, cannot hold a PCoC, and cannot answer the platform. Every document you prepare feeds your importer's application.

      Two certificates, two clocks. The Product Certificate of Conformity is issued per model, valid one year, reviewed by a SASO-approved body, platform fee SAR 500. The Shipment Certificate of Conformity is issued per consignment and links to a valid PCoC, fee SAR 350. Its validity moved from 60 days to 90 days in September 2026, since a slow transhipment no longer kills the certificate before the box reaches Dammam.

      Everything else tightened. The platform now takes the twelve-digit Saudi HS code; eight- and ten-digit codes are rejected. Wildcard model numbers are gone, so every variant appears by model. The channel that once allowed release against a letter of commitment was withdrawn in 2025, ending the option of fixing paperwork after arrival.

      Because SABER is integrated with FASAH, the officer at the border is not reading your folder but a database record, and a shipment with no matching SCoC is re-exported.

      ✅ Bottom line: The certificate is not a document you produce. It is a record your importer creates from documents you produce.

      4. Where a compliant box still fails

      A box can clear the border and be rejected at submittal, because the installation layer is a different code with a different owner. The Saudi Electrical Code, SBC 401, is in its third edition — the 2024 text — mandatory since 30 June 2025. Built on IEC 60364 with Saudi amendments, it covers installations to 1000 V AC at 60 Hz and is enforced through permitting on the Balady platform and an occupancy certificate. Administration moved from SASO to the Saudi Building Code Center in 2025.

      Three consequences land on the enclosure. Sixty hertz changes nothing about a busbar and everything about a magnetic device's calibration. A 50 °C design ambient is not the 40 °C of the IEC baseline: a breaker rated 1000 A at 40 °C de-rates to roughly 800 to 850 A at 50 to 55 °C, which is why frames get picked a size above the load schedule. And the enclosure has to survive dust, sun load and coastal salt — IP65 outdoors, 316L stainless and a C5-M paint system near the Gulf.

      Above the code sits the project. Aramco's 16-SAMSS-518 for low-voltage switchgear and 16-SAMSS-503 for control centres set 2.0 mm minimum sheet, Form 4b separation and verified performance at 50 °C continuous, all of which a catalogue board fails. None of it shows in a SABER certificate, which is why custom distribution box OEM for Saudi projects is a design conversation rather than a purchase order. LUJIEMAO quotes against the drawing, not the catalogue.

      5. The pack that clears

      Assemble this before the importer opens the application: a permanent Arabic-and-English nameplate with model, ratings, manufacturer, origin and the importer's CR, warnings translated rather than transliterated; an Arabic manual; a declaration naming IEC 61439-1 and -2 and the edition verified, not the series; the design verification file plus a routine record for the unit shipped; the EMC report; the RoHS certificate.

      Send the load schedule, ambient temperature and project specification to Wenzhou Lujiemao Electric Co., Ltd. and LUJIEMAO will return a layout, a device list and the verification documents that go with it. The build runs from our factory in Yueqing on wholesale terms for project quantities, with built-to-specification variants quoted against the consultant's drawing. Start with the construction site power box range or the outdoor weatherproof power cabinet range, then send the schedule to our supplier team.

      Saudi project distribution box with Arabic and English nameplate, SABER PCoC documentation and IEC 61439 declaration

      For how the same assembly is judged elsewhere, read LUJIEMAO's comparison of UK, Australian, GCC and US construction site distribution board requirements.

      Frequently asked questions

      Q: Does a distribution box need a G-Mark to enter Saudi Arabia?

      A: Not under the current lists. List 2 names thirteen categories and none is an assembly; List 1 has never been published. What the box needs is a SABER PCoC and, per shipment, an SCoC. When a specification asks for a mark, ask which list item it cites — the answer is the whole of G-Mark certification requirements for distribution boxes in Saudi Arabia.

      Q: Can the manufacturer apply instead of the importer?

      A: No. The SASO SABER registration process for imported distribution boxes always runs through the importer, because registration requires a Saudi commercial registration. The account, the certificate and the liability stay Saudi. Wenzhou Lujiemao Electric Co., Ltd. assembles every input — reports, drawings, bilingual artwork, the declaration — but the application is filed from Riyadh.

      Q: One PCoC lasts a year — does it cover a product family?

      A: Only the models printed on it. Wildcard numbers were removed, and each variant must appear by model. A different enclosure size or device complement is a different model, so the certificate is amended before an SCoC can be issued — which is why custom distribution box OEM for Saudi projects freezes the drawing before the application, not after.

      Q: Is IEC 61439-4 the standard a Saudi reviewer expects?

      A: Expect IEC 61439-1 and -2. SASO adopted those two as national standards, while Part 4 appears in the EMC regulation's list under its plain IEC designation, with no SASO prefix. Submit against -1 and -2, and declare -4 where the assembly genuinely is a site assembly. LUJIEMAO states which edition was verified, because a declaration naming the series rather than the edition is the first thing a reviewer rejects.

      http://www.lujiemao.com
      Wenzhou Lujiemao Electric Co., Ltd.

    Viewing 1 post (of 1 total)
    • You must be logged in to reply to this topic.